Study of the synergistic effect of boron nitride and carbon nanotubes in the improvement of thermal conductivity of epoxy composites

The enhancement of the thermal conductivity, keeping the electrical insulation, of epoxy thermosets through the addition of pristine and oxidized carbon nanotubes (CNTs) and microplatelets of boron nitride (BN) was studied. Two different epoxy resins were selected: a cycloaliphatic (ECC) epoxy resin and a glycidylic (DGEBA) epoxy resin. The characteristics of the composites prepared were evaluated and compared in terms of thermal, thermomechanical, rheological and electrical properties. Two different dispersion methods were used in the addition of pristine and oxidized CNTs depending on the type of epoxy resin used. Slight changes in the kinetics of the curing reaction were observed in the presence of the fillers. The addition of pristine CNTs led to a greater enhancement of the mechanical properties of the ECC composite whereas the oxidized CNTs presented a greater effect in the DGEBA matrix. The addition of CNTs alone led to a marked decrease of the electrical resistivity of the composites. Nevertheless, in the presence of BN, which is an electrically insulating material, it was possible to increase the proportion of pristine CNTs to 0.25 wt% in the formulation without deterioration of the electrical resistivity. A small but significant synergic effect was determined when both fillers were added together. Improvements of about 750% and 400% in thermal conductivity were obtained in comparison to the neat epoxy matrix for the ECC and DGEBA composites, respectively. © 2019 Society of Chemical Industry     

A novel temperature-tolerant foamed resin for enhanced oil recovery

The synthesis and performance of a novel temperature-tolerant foamed resin for enhanced oil recovery were investigated using various methods, including infrared, NMR, scanning electron microscopy (SEM), and displacement experiments. Polycondensation of furfuryl alcohol prepolymers was confirmed by the infrared and NMR results. The poor temperature tolerance of furfuryl alcohol prepolymers after gelation at high temperatures is mainly due to the fracture of furan rings. The addition of ester additives is an effective method of increasing the temperature tolerance of the prepared foamed resins and can effectively reduce the weight-loss rate of the polycondensation products. The SEM results show that the skeleton structure of the foamed resin remains intact after high-temperature treatment. Thus, the novel plugging agent system has excellent thermal stability and still has a high strength (>0.8 MPa) after high-temperature aging treatment for 40 days, giving the prepared foamed resin a good plugging performance (plugging rate > 91%) at 250 °C. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47161.     

Separation of Indium from Acid Sulfate-Containing Solutions by Ion Exchange with Impregnated Resins

Indium separation using ion exchange resins from acidic polymetallic and very diluted solutions are investigated. Since the selectivity of commercial ion exchange resins have proven to be too low for an effective separation from solutions with high content of other metals, Lewatit® TP 208 was impregnated with common extractants to enhance its properties. By resin impregnation with D2EHPA and Cyanex 272, not only the selective indium recovery was reached but also the resin capacity was increased approx. two times. The best loading and elution performance were shown by Cyanex 272-impregnated Lewatit® TP 208, increasing the indium purity in the eluate from 0.75 % to 85 %.     

Effects of diacrylate monomers on the bond strength of polymer concrete to wet substrates

The bond strengths of polymer concretes containing up to 15% (based on polymer resin) of diacrylate (DA) monomers were examined and compared with those without DA. A change occurring with the addition of DA monomers was an increase in the bond strength of polymer concrete to wet substrates. Zinc diacrylate (ZDA) and calcium diacrylate (CDA) were each used as an additive to monomers and resins [methyl methacrylate (MMA), polyester, and two kinds of epoxies]. The variables were amount of the DA monomers and surface conditions (wet or dry and smooth or rough). Bond strengths were measured by tension bond. ZDA was found to improve the bond strength of MMA and polyester, whereas CDA improved the bond strength of epoxies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 991–1000, 2003     

水溶性丙烯酸涂料的环氧树脂改性

本实验论述了水溶性丙烯酸钢铁底漆涂料制备、性能以及用环氧树脂对其进行改性。原水溶性丙烯酸钢铁底漆涂料在进行耐盐雾测定试验时仅为 72h ,未通过国家规定标准。本实验的目的在于 ,以丙烯酸树脂为主要成膜物质 ,加入其他的辅助成膜物质 ,如环氧树脂来改善其抗盐雾、抗腐蚀、耐候等性能。结果表明 ,一定温度下在水溶性丙烯酸钢铁底漆涂料中加入 1/ 7的环氧树脂后 ,经测定其耐盐雾性可达 10 6h ,达到了国家的规定标准     

Structural acrylic adhesives for the sheet steel fabrication industries

Recent developments in rubber-toughened structural acrylic adhesives now offer sheet steel fabricators the opportunity to replace conventional metal fastening techniques such as spot welding with lower cost, durable, more versatile structural adhesive bonding. These developments, in particular much improved ability to bond oily/waxy surfaces common to the motor car industry and improved retention of fracture toughness after exposure to paint stoving temperatures, are discussed in this paper.     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.     

Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

反渗透膜仓用韧性环氧树脂基体研究

工业上广泛使用反渗透膜仓制备高纯水,为了用玻璃钢替代不锈钢,研究了一种适合湿法缠绕的反渗透膜仓用韧性环氧基体。在配方中采用液体酸酐固化剂甲基四氢邻苯二甲酸酐和高效活性增韧剂,对树脂基体和复合材料力学性能及耐水性能的研究表明该树脂基体具有许多优良性能,如拉伸强度≥86.2MPa,断裂延伸率≥5.2%,弯曲强度≥139MPa,制得膜仓爆破时纤维强度转化率高达88.7%,耐疲劳达10万次而无损伤。此外,配方体系室温下粘度为0.35～0.4Pa·s,适用期≥8h,室温下在水中浸泡180d后吸水率低于0.5%,同不锈钢相比成本降低1/2。实验结果表明,该韧性环氧基体完全适用于反渗透膜仓使用。